CVE-2026-80712 - spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
CVE ID :CVE-2026-80712
Published : Aug. 28, 2026, 8:16 a.m. | 2 hours, 13 minutes ago
Description :In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: write the feature value before executing SET_FEATURE qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits the descriptors, which makes the controller execute the command immediately. For SPINAND_SET_FEATURE the value to be written is only placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a second submission - so the chip is programmed with whatever that register happened to hold from a previous operation, and the intended value is only applied by the *next* SET_FEATURE. Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing 0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the subsequent write of 0x00 leaves it at 0x40 - every write lands one operation late. This stayed unnoticed until v6.18 added SPI-NAND OTP support together with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode, reads, and disables it again, and mtd_otp_nvmem_add() does this during MTD registration. With the off-by-one, the "disable" write actually applies the previously requested value, so CFG_OTP_ENABLE ends up set: the chip stays in OTP mode, every subsequent array read returns the OTP area instead of the array (UBI reports an empty device) and all writes fail with -EIO because the OTP area is write protected. On this board that makes the whole flash unusable and the device unbootable. Write the feature value into NAND_FLASH_FEATURES as part of the same transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the operation actually carries - the previous code dereferenced a 4-byte pointer on a one-byte buffer (spinand->scratchbuf). With this patch the flash contents read back bit-identical to a known-good dump of the same board taken under the vendor firmware (md5-verified across partitions), and writes work.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
Published : Aug. 28, 2026, 8:16 a.m. | 2 hours, 13 minutes ago
Description :In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: write the feature value before executing SET_FEATURE qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits the descriptors, which makes the controller execute the command immediately. For SPINAND_SET_FEATURE the value to be written is only placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a second submission - so the chip is programmed with whatever that register happened to hold from a previous operation, and the intended value is only applied by the *next* SET_FEATURE. Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing 0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the subsequent write of 0x00 leaves it at 0x40 - every write lands one operation late. This stayed unnoticed until v6.18 added SPI-NAND OTP support together with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode, reads, and disables it again, and mtd_otp_nvmem_add() does this during MTD registration. With the off-by-one, the "disable" write actually applies the previously requested value, so CFG_OTP_ENABLE ends up set: the chip stays in OTP mode, every subsequent array read returns the OTP area instead of the array (UBI reports an empty device) and all writes fail with -EIO because the OTP area is write protected. On this board that makes the whole flash unusable and the device unbootable. Write the feature value into NAND_FLASH_FEATURES as part of the same transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the operation actually carries - the previous code dereferenced a 4-byte pointer on a one-byte buffer (spinand->scratchbuf). With this patch the flash contents read back bit-identical to a known-good dump of the same board taken under the vendor firmware (md5-verified across partitions), and writes work.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...