CVE-2026-79982 - Out-of-bounds write in the USB Bluetooth HCI transport class when a controller-to-host HCI packet exceeds the bulk endpoint maximum packet size
CVE ID :CVE-2026-79982
Published : Oct. 23, 2026, 7:56 p.m. | 25 minutes ago
Description :The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.
Severity: 8.8 | HIGH
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
Published : Oct. 23, 2026, 7:56 p.m. | 25 minutes ago
Description :The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.
Severity: 8.8 | HIGH
Visit the link for more details, such as CVSS details, affected products, timeline, and more...